Our Ultimate Polar Bundle contains everything you need to clean and protect your vehicle exterior. Hook up the Polar Blaster snow foam lance to your pressure washer and spray on a trio of Polar products to give your vehicle the ultimate wash experience. Polar Blast is our super thick snow foam used to pre-wash soak your vehicle to loosen and soften dirt. Polar Wash is our spray-on shampoo, use this and a wash mitt to remove any remaining dirt from the vehicle. Now spotlessly clean, finally spray on Polar Seal to seal and protect your gleaming bodywork. Polar Seal improves shine and gloss and even repels water to make drying easier.

The Polar Blaster can be used with a range of pressure washers. A Karhcer K series fitting comes as standard, for other pressure washer makes, see our Polar Blaster adaptors range.

Includes:

• Polar Blaster snow foam lance
• Polar Blast 2.5L
• Polar Wash 2.5L
• Polar Seal 1L

‍

Polar Blast

1. Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
2. Polar Blast can be used at various dilutions depending on the density of foam desired. A good starting point is 100ml product to 500ml water in your foaming bottle. Adjust foam gun settings as required to increase or reduce foam.
3. Spray Polar Blast onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass and wheels.
4. Leave Polar Blast time to dwell and loosen dirt for up to 10 minutes, although do not allow it to dry on.
5. Finally, rinse thoroughly from the bottom up.  

Polar Wash

1. Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
2. We recommend a pre-wash with Polar Blast to gently loosen dirt. If not, rinse first with water to loosen heavy contamination.
3. Polar Wash can be used at various dilutions depending on the density of foam desired. However, we would not recommend using a dilution stronger than 50:50. Adjust foam gun settings as required to increase or reduce foam. 250ml of mixed solution should be enough to cover an average sized car.  
4. Spray Polar Wash onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass and wheels.
5. The cleaner will begin to loosen dirt on all surfaces. For the most thorough clean we recommend agitating the foam with a sponge or wash mitt.
6. Rinse thoroughly from the bottom up and dry.

Polar Wash is not suitable for use on soft top convertibles.

Top Tip – Follow with Polar Seal for a protective, hydrophobic coating

Polar Seal

1. Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
2. We recommend starting with a snow foam like Polar Blast to gently loosen dirt, and follow with Polar Wash to remove any dirt or contamination on your paintwork.
3. Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle and then add at least 200ml of water. This should be all the finished solution required to cover your vehicle. There is no benefit in using any more than 40ml as over application can compromise the finish.
4. Spray Polar Seal onto the clean, wet vehicle, ensuring all exterior surfaces are covered, although avoid direct application to the windscreen.
5. Thoroughly rinse and dry your car to reveal a high-gloss finish that is protected with a hydrophobic coating. The car must be dried with a cloth and not allowed to air dry as water spotting may occur.
6. Use Autoglym Fast Glass to clean the windscreen and wiper blades to ensure no smearing occurs.

We do not recommend applying more than once a month.

Polar Seal is not suitable for use on soft top convertibles.

Do not store diluted product. Please rinse foam bottle and pressure washer lance after use.

Avoid contact of the neat product with surfaces such as tarmac, paved surfaces or concrete.

Top Tip – For the optimum finish, dry with the Autoglym InstaDry cloth.

Polar Blaster

Polar Blaster Assembly:

1. Attach the clear Pickup Tube (C) to the brass nozzle on the underside of the Foam Gun Head (B).
2. Attach the black end of the Connector (A) to the hand gun on your pressure washer.
3. Pull back the spring-loaded brass collar on the Connector (A) and connect it to the silver nozzle on the Foam Gun Head (B).

Polar Blaster In Use:

1. Dilute the product at the recommended rate, outlined on the sidewall of the Polar reservoir bottle (D).
2. Screw the Foam Gun Head (B) onto the Polar reservoir bottle (D) and attach the Polar Blaster to your pressure washer lance.
3. Aiming at the floor, pull the trigger on your pressure washer, allowing the Polar product to feed through.
4. Turn the Dial (E) to adjust the foam level and turn the Nozzle (F) to change the spray pattern.
5. Once the Polar product has fed through at the desired level, begin applying to your car in accordance with the relevant Polar Series product instructions.
6. Rinse the reservoir bottle with clean water after using it with each product.
7. Flush through the Polar Blaster with clean water when you have finished using it to apply all intended products.

The Connector (A) is compatible with the Karcher K-Series of pressure washers.

‍